The Parasound NewClassic 275 V.2 stereo amplifier offers 90 watts at 8 ohms into each channel and 150 watts at 4 ohms. You can also bridge the 275 v.2 transforming it into a 200-watt mono amplifier.
Parasound NewClassic 275 V.2 Features and Specifications:
- 90 watts x 2 into 8 Ω (all channels driven)
- 150 watts x 2 into 4 Ω or 2 Ω (all channels driven)
- 200 watts x 1 bridged into 8 Ω or 4 Ω
- 20 amps peak current per channel
- 2 Ohm stable operation with load selector switch
- Two pairs of speaker outputs with front panel A/B buttons
- Rear-mounted lockout switch disables front A/B buttons
- High pass filter, switchable for 20Hz or 40Hz
- Automatic on/off by DC trigger with looping output
- Automatic on/off by audio signal with 2 sensitivity settings
- Fully discrete circuitry with a high current toroid transformer
- Bridging switch for stereo or mono operation
- Efficient, low heat design
- DC Servo and relay protection circuits
- Rear-mounted left and right gain controls
- Standby, channel status and high-temperature indicators
- Gold-plated RCA input jacks
- Heavy-duty 24k gold-plated 5-way speaker terminals
- 115/230v selector on the rear panel
- 1U rack mount kit available separately (Model RMK11)
Specifications:
- Power Output – (RMS power, 20 Hz – 20 kHz)
All Channels Driven
90 watts x 2, 8Ω
150 watts x 2, 4Ω
150 watts x 2, 2Ω (Load switch set to 2-3Ω) - Bridged Mono
200 watts x 1, 8Ω
200 watts x 1, 4Ω (Load switch set to 2-3Ω) - Current Capacity
20 amps peak per channel - Frequency Response
20 Hz – 50 kHz, +0/-3 dB, 1 watt - Dynamic Headroom – 1.3 dB
- Total Harmonic Distortion
0.35% at full rated output
0.025% at average listening levels - IM Distortion – 0.05 %
- Transient IM Distortion – Not measurable
- S/N Ratio
110 dB at rated output, IHF A-weighted
103 dB at rated output, unweighted
93 dB at 2.828 V output, IHF A-weighted
84 dB at 2.828 V output, unweighted - Input Impedance – 33 k Ω
- Input Sensitivity
800 mV for full rated output (28dB) - Inter-Channel Crosstalk
80 dB @1 kHz, 72 dB @10 kHz, 65 dB @ 20kHz - Damping Factor – Over 150 at 20Hz
- 12V Trigger Turn On – DC 9 – 12V, 15 mA
- Audio Turn On
Quieter: 1 mV
Louder: 6 mV - AC Power Requirement
110 – 120 V / 220 -240 V, 50 – 60 Hz
0.5 watts standby
25 watts Idle (no audio)
350 watts full output - Dimensions
17-1/4″ Wide
16″ Deep, with cables connected
2-1/2″ High with feet, 1-3/4″ panel only (1U)
(437 x 406 x 63mm, 44.1 mm panel only) - Net Weight – 20 lbs (9.1 kg)
- Rack Mount Accessory
Purchased Separately
RMK11
Reviews
There are no reviews yet.