Mon-Fri 9am - 5.30pm / Sat 9am - 5pm / Sun - Closed
FREE SHIPPING IN AUS(Orders Over $300)

Parasound 275 V2 2 Channel Power Amplifier

$1,199.00 inc. GST

Description

90 watts x 2 into 8 Ω (all channels driven)
• 150 watts x 2 into 4 Ω or 2 Ω (all channels driven)
• 200 watts x 1 bridged into 8 Ω or 4 Ω
• 20 amps peak current per channel
• 2 Ohm stable operation with load selector switch
• Two pairs of speaker outputs with front panel A/B buttons
• Rear-mounted lockout switch disables front A/B buttons
• High pass filter, switchable for 20Hz or 40Hz
• Automatic on/off by DC trigger with looping output
• Automatic on/off by audio signal with 2 sensitivity settings
• Fully discrete circuitry with high current toroid transformer
• Bridging switch for stereo or mono operation
• Efficient, low heat design
• DC Servo and relay protection circuits
• Rear-mounted left and right gain controls
• Standby, channel status and high temperature indicators
• Gold-plated RCA input jacks
• Heavy duty 24k gold-plated 5-way speaker terminals
• 115/230v selector on rear panel
• 1U rack mount kit available separately (Model RMK11)

 

 

  • Power Output – (RMS power, 20 Hz – 20 kHz)
    All Channels Driven
    90 watts x 2, 8Ω
    150 watts x 2, 4Ω
    150 watts x 2, 2Ω (Load switch set to 2-3Ω)
  • Bridged Mono
    200 watts x 1, 8Ω
    200 watts x 1, 4Ω (Load switch set to 2-3Ω)
  • Current Capacity
    20 amps peak per channel
  • Frequency Response
    20 Hz – 50 kHz, +0/-3 dB, 1 watt
  • Dynamic Headroom – 1.3 dB
  • Total Harmonic Distortion
    0.35% at full rated output
    0.025% at average listening levels
  • IM Distortion – 0.05 %
  • Transient IM Distortion – Not measurable
  • S/N Ratio
    110 dB at rated output, IHF A-weighted
    103 dB at rated output, unweighted
    93 dB at 2.828 V output, IHF A-weighted
    84 dB at 2.828 V output, unweighted
  • Input Impedance – 33 k Ω
  • Input Sensitivity 
    800 mV for full rated output (28dB)
  • Inter-Channel Crosstalk
    80 dB @1 kHz, 72 dB @10 kHz, 65 dB @ 20kHz
  • Damping Factor – Over 150 at 20Hz
  • 12V Trigger Turn On – DC 9 – 12V, 15 mA
  • Audio Turn On
    Quieter: 1 mV
    Louder: 6 mV
  • AC Power Requirement
    110 – 120 V / 220 -240 V, 50 – 60 Hz
    0.5 watts standby
    25 watts Idle (no audio)
    350 watts full output
  • Dimensions
    17-1/4″ Wide
    16″ Deep, with cables connected
    2-1/2″ High with feet, 1-3/4″ panel only (1U)
    (437 x 406 x 63mm, 44.1 mm panel only)
  • Net Weight – 20 lbs (9.1 kg)
  • Rack Mount Accessory
    May be Purchased Separately
    RMK11

Additional Information

Enquiry