The Krix MX-10 Package has been put together to provide you with an idea of what the speaker component of an MX-10 theatre will cost. We have included 5.2.2, 5.2.4, 7.2.2 and 7.2.4 speaker configurations to cover most room layouts depending on room size.
Choosing the right Krix speaker package for your Room:
We would prefer to guide you through the process of choosing the right speakers for your room and budget to achieve maximum end results. We have listed the guide below to get you started
What we need from you
- Room Dimensions
- How many people do you wish to seat in the room
- What is your expectation of the end result
- What is your budget
With this information, we will guide you through the selection process which includes the key points below
- Choosing the correct MX system for your room
- Selecting the correct speaker configuration for your room
- Matching an AV receiver or pre/power combination to drive your Krix speaker system
- Guide you through your projection options including the correct screen size
- Discuss if you wish to DYI or use our in-house installation team to pre-wire and install your Krix cinema
Please visit our Castle Hill showroom or contact our friendly staff for more information!
The Krix MX-10 Package Includes;
The Krix MX-10 Package is a speaker-only package please talk to our friendly staff about adding an AV Reciever, projector screen, cabling etc.
- Krix MX-10 speaker wall
- Krix IW-50 in-wall surround and rear surround speakers
- Krix IC-52 in-ceiling Mounted Atmos speakers
- Krix KA-1100 subwoofer amplifier
- Krix banana speaker cable terminations for amplifier
- In-Wall & In-Ceiling speakers available in cinema black at an extra cost
Note:
Please contact a builder or handyman for advice and pricing for wall construction, we can supply a construction info sheet with requirements and dimensions.
Krix MX-10 Package Component Information:
Krix MX10 Information:
Designed for dedicated home cinemas with an acoustically transparent screen, the MX-10 is a superb choice for those seeking an involving cinema experience with crystal clear intelligibility, large dynamic range and powerful bass.
- Easy to install
- Krix Infinite Baffle Wall
- For medium-sized rooms
LCR SPEAKER MODULE Specs:
Frequency Range
40Hz-20kHz in-room response
Power Handling
50 – 200 Watts RMS recommended amplifier power
Sensitivity
97dB for 2.83 volts at 1 metre
Impedance
8 Ohms
Configuration
2-way
Enclosure Type
Bass reflex, front vented
Low-Frequency Driver
Single 255mm (10”) paper cone driver. 50mm (2”) voice coil wound on high-powered Kapton former, with ventilated magnet assembly and copper shorting ring for low distortion
High-Frequency Driver
26mm (1”) doped fabric dome with a large roll surround. Ferrofluid cooled. Coupled to a Krix-designed 90 x 40 short-throw waveguide
Input Terminals
Gold plated spring terminals
Dimensions
940mm high x 315mm wide x 205mm deep (2025mm wide including subwoofer modules)
SUBWOOFER MODULES
Frequency Range
25Hz-200Hz in-room response
Power Handling IEC AES
450 Watts
Power Handling Program
900 Watts
Sensitivity
92dB for 2.83 volts at 1 metre
Impedance
4 Ohms
Enclosure Type
Bass reflex, down-firing vent
Low-Frequency Driver
Nominal 305mm (12”) diameter paper cone driver with 50mm (2”) long-throw voice coil developed for high level, low-frequency reinforcement
Input Terminals
High-level gold plated spring terminals
Dimensions
940mm high x 540mm wide x 205mm deep (2025mm wide including LCR modules)
SYSTEM RECOMMENDATIONS
Min. Screen Size 16:9
92″ (2037mm x 1146mm)
Minimum Screen Size 21:9
100″ (2335mm x 1001mm)
Krix IW-50 Information:
- Exceptional concealed performance
- Fits inside a 70mm wall cavity
- Fully enclosed backbox
- Trimless magnetic grille
- available in black at an extra cost
Frequency Range
55Hz-40kHz in-room response
Power Handling
20 – 140 Watts RMS recommended amplifier power
Sensitivity
89dB for 2.83 volts at 1 metre
Impedance
Nominally 6 Ohms (minimum 3.5 Ohms)
Configuration
D’Appolito, 2-way
Cut-out Dimensions
555mm x 170mm recommended
Dimensions
596mm high x 211mm wide x 79mm mounting depth
Low-Frequency Drivers
2 x nominal 100mm (4”) doped paper cones. 25mm (1”) voice coil wound on high-temperature Kapton former
High-Frequency Driver
26mm (1”) dual concentric diaphragm with wave-guide centre plug for controlled directivity. Neodymium magnet
Input Terminals
Gold plated spring terminals
Enclosure Type
Bass reflex, front vented
Weight
4kg each
Krix IC-52 Information:
Low-Frequency Driver
Cast aluminium basket with a nominal 130mm (5″) doped curvilinear paper cone. 25mm (1″) voice coil wound on high-powered aluminium former with copper shorting ring. Vented and double magnet shielded
High-Frequency Driver
26mm (1”) ring radiator tweeter
Input Terminals
Gold plated spring terminals
Frequency Range
45Hz-40kHz in-room response
Power Handling
20 – 120 Watts RMS recommended amplifier power
Sensitivity
90dB for 2.83 volts at 1 metre
Impedance
Nominally 6 Ohms (minimum 3.9 Ohms)
Configuration
2-way
Enclosure Type
Bass reflex, front vented
Dimensions
295mm diameter x 193mm mounting depth
Cut-out Diameter
247mm recommended
Weight
2.5kg each
